Carrier Manual Outside Air Damper
Manual Outside Air Damper 060 These accessory manual outside air damper packages can be used in either a horizontal or vertical discharge application. Sep 24, 2015 - The idea is to manually set the blade located inside the hood to restrict the opening by introducing Static Pressure, thereby balancing the outside air with the return air entering the RTU. Manual Damper Hood At MicroMetl The drawback to a manual damper is that it is open 24 hours a day, 365 days a year.
• Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. PC 111 Catalog No. 534-774 Book 1 1a 6a 48TJD,TJE,TJF005-007 Page Disconnect gas piping from unit when leak testing at pressure greater than sures greater than damage resulting in hazardous condition. • Curb should be level. Unit leveling tolerances are shown in Fig. This is necessary for unit drain to function properly. Call Of Juarez Gunslinger Crack Only Reloaded.
Re- fer to Accessory Roof Curb Installation Instructions for addi- tional information as required. SLAB MOUNT (Horizontal Units Only) — Provide a level concrete slab that extends a minimum of 6 in. • ‘‘D’’ ALT ‘‘E’’ ‘‘B’’ ‘‘C’’ DRAIN HOLE Power ″ [19] NPT [19] NPT ″ ″ [31.7] 1′-9 1′-4″ [551] [406] [44.5] ″ [12.7] NPT [19] NPT ″ [19] NPT [31.7] TO ENSURE AIRTIGHT CONNECTION PLACE UNIT AS CLOSE TO END AS POSSIBLE. TO ENSURE AIRTIGHT CONNECTION PLACE UNIT AS CLOSE TO END AS POSSIBLE. • MAXIMUM ALLOWABLE DIFFERENCE (in.) Fig. 3 — Unit Leveling Tolerances CONDENSATE PAN (SIDE VIEW) DRAIN PLUG NOTE: Drain plug is shown in factory-installed position. 4 — Internal Trap Condensate Drain POSITIONING — Maintain clearance around and above unit to provide minimum distance from combustible materials, proper airflow, and service access.
• The sheet metal is located adjacent to the corner post on the left side of the power wiring access panel. WEIGHT UNIT 48TJE,TJF004 510 231 48TJD,TJE,TJF005 520 236 48TJD,TJE,TJF006 540 245 615 279 48TJD,TJE,TJF007 Fig. 5 — Rigging Details FIELD POWER SUPPLY —. • UNIT SIZE 48TJ NOMINAL CAPACITY (tons) OPERATING WEIGHT (lb) Unit Al/Al* Al/Cu* Cu/Cu* Economizer Durablade EconoMi$er Roof Curb† COMPRESSOR Quantity No. Cylinders (per Circuit) Oil (oz) REFRIGERANT TYPE Expansion Device Operating Charge (lb-oz) Circuit 1 Circuit 2 CONDENSER COIL Rows. Concrete Slab Crack Inducer. Fins/in. Total Face Area (sq ft) CONDENSER FAN Nominal Cfm.
• UNIT SIZE 48TJ FURNACE SECTION Rollout Switch Cutout Temp (F)†† Burner Orifice Diameter (in.drill size) Natural Gas Liquid Propane Thermostat Heat Anticipator Setting (amps) 208/230 v and 575 Stage 1 Stage 2 460 v Stage 1 Stage 2 Gas Input (Btuh) Stage 1 Stage 2 Efficiency (Steady State) (%) Temperature Rise Range. • STANDARD DURABLADE ECONOMI$ER UNIT ECONOMIZER UNIT WEIGHT WEIGHT WEIGHT 48TJ E/F004 15.4 21.3 D/E/F005 15.4 21.3 D/E/F006 15.4 21.3 D/E/F007 15.4 21.3 CONNECTION SIZES ″ ″ ″ ″ Dia [27] Field Power Supply Hole ″ ″ ″ ″ -14 NPT Condensate Drain ″. • Such operation would invalidate any applicable Carrier warranty. FIELD CONTROL WIRING — Install a Carrier-approved accessory thermostat assembly according to installation in- structions included with the accessory. Device Driver Manager For Linux Mint on this page. Locate thermostat. • 208/230-1-60 575-3-60 (SIZE 007 ONLY) LEGEND — Contactor COMP — Compressor — National Electrical Code — Terminal Block Fig.